10 Unexpected Peugeot Keys Tips
Peugeot 208 Key Replacement
It is recommended to leave the replacement of Peugeot keys 208 to auto locksmiths equipped with the required equipment and knowledge. They can design and program keys more quickly and at a lower cost than dealers.
If the key fob stopped locking or unlocking your doors, it could be due to a dead coin battery. There are other reasons the key could be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. In this scenario you'll need to choose the alternate method to start described in your vehicle owner's manual.
peugeot 206 key why your 208 might not start is that the spark plugs are been worn down. Spark plugs are what ignite the fuel to start the engine. However, they have a limited lifespan. They'll eventually degrade if they're not used enough.
There is a simple solution for this problem. The best option is to measure the voltage of your car battery with a multimeter. If the voltage is lower than 11,5 volts, then it's time to replace it. If the battery is corroded it is necessary to clean its contacts. This can be done by removing the rubber cover from the two terminals on the battery and then using a wirebrush, you can remove any damaged parts of the battery. Then, reconnect the cables that connect the positive and negative poles.
Water Damage
If your 208 won't turn on and the battery is not running, then make sure whether the spark plugs are functioning. You might find that they're dirty and don't spark. This can be easily corrected by cleaning the spark plugs in the workshop.
Peugeot automobiles use a key with a transponder that is compatible with the immobiliser. This makes sure that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle.
This is a typical issue that can be caused by water damage. This is most common in colder climates where the vehicle may have been exposed to rain or snow. In this case, contact an experienced locksmith who will have the necessary tools and equipment to modify the key. They will also have all the latest technology and machinery needed to create a Peugeot smart key. The process shouldn't last more than 15 minutes.
Faulty battery contacts
Peugeot replaced the transponder chips by introducing a new model that is based on electronic components that are mounted on a circuitboard. The new system works great in its initial state, but the circuit boards deteriorate over time and stop working properly.
This could prevent the immobiliser from working, so your vehicle won't start. If this is the case, it's a good idea call a Peugeot specialist or locksmith.
A common issue occurs when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car can replace the battery and cut a new blade for you, it's usually a simple fix.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, being exposed to a sudden rain or accidently washing it or washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer that manages the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals that block water from getting to the electronic chip inside. The chip can be damaged by water if it is exposed to water for a long time. Submerging the key fob into ocean water at the beach or throwing it into the water can be especially damaging because of the high salt content.
If your Peugeot spare key fob stops working, you'll need to have the module replaced. This should be done by an Peugeot specialist or an expert auto locksmith. Unlike other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct coding to start the engine. This is why it is imperative that you should only trust a Peugeot locksmith to create and program an alternative.
Computer on-board is not working properly
The on-board computer of your Peugeot is responsible for many of the systems inside your car, including airbags and power windows. If something is wrong with these systems, it'll typically display a code that identifies the problem. This code will be saved in the system until the issue is fixed. Usually, this will mean the on-board computer being replaced.
The most typical reason for the airbag warning light to turn on is corrosion or loose connections in the sensor. This can occur due to wear and tear, ageing or exposure to salt and moisture. This issue should be addressed as soon as you can, because an airbag that is not functioning could pose a risk in the event of an accident.
If your Peugeot is showing a card that is not being detected error, then the battery in the key fob may be weak or dead. This will stop the key fob from sending a signal that will disable the immobilizer in your vehicle. Test this by pressing the unlock button on the key fob, and then trying to start your vehicle. If this doesn't work then the battery in the key needs to be replaced.